机械 中文译英文概述本公司生产的CYQ型厨记除油器能有效的去除水中各种浮油及其它比生小于水的液体,并能做到油水分离废油回收,其原理是利用油水之间不同重力和表面张力等特性.广泛的

机械 中文译英文概述本公司生产的CYQ型厨记除油器能有效的去除水中各种浮油及其它比生小于水的液体,并能做到油水分离废油回收,其原理是利用油水之间不同重力和表面张力等特性.广泛的
机械 中文译英文
概述
本公司生产的CYQ型厨记除油器能有效的去除水中各种浮油及其它比生小于水的液体,并能做到油水分离废油回收,其原理是利用油水之间不同重力和表面张力等特性.广泛的被用于厨房灰水处理,也适用于船舶、舰艇、平台等厨房灰水处理.与同类型产品相比,具有体积小,重量轻,结构紧凑.本装置符合MARPOL73/78公约要求.
二、安装
本装置的安装尽可能处于水平位置,装置的底座上设有螺孔.
装置附有固定船舶结构上的底座,其底座尺寸和固定孔位置,详见下图.
装置处于船舶管路相连接的灰水入口,排放口,溢流口中,泄放口等管路其连接方式与尺寸,详见总图.
三、操作
装置运行前先注入清水,注入的清水量为能在观察颜观孔见到水面即可.
关闭泄放阀,打开溢流口阀,此时装置即可运行.当装置内油累积到从观察孔看不到水时需进行排油动作,打泄放阀即可.
注：
1.打开装置盖板,将不锈钢丝网抽出并清洗干净；
2.拧开装置底部放泄螺塞；
3.关闭出口阀,打开溢流口阀及放泄阀,用清水清洗.
4.用棉布将观察孔玻璃擦试干净.
要手动的 机译的不要

机械 中文译英文概述本公司生产的CYQ型厨记除油器能有效的去除水中各种浮油及其它比生小于水的液体,并能做到油水分离废油回收,其原理是利用油水之间不同重力和表面张力等特性.广泛的
Overview of the company's CYQ-type kitchen in mind oil remover can effectively remove all the oil slick water and other liquids than raw water is less than, and can be recycled waste oil water separator, the principle is to use the differences between oil and water gravity and surface tension and other characteristics. Widely used for kitchen gray water treatment, also apply to ships, vessels, platforms and other kitchen gray water treatment. Compared with the same types of products, small volume, light weight, compact structure. This device complies with MARPOL73/78 requirements of the Convention. Second, the installation of this device installed in a horizontal position as much as possible, the base unit with screw. Device with a fixed base on the ship's structure, its base dimensions and mounting hole locations, see the figure below. Device is connected to the ship's gray water pipe entrance, outlet, overflow mouth, mouth, such as pipe discharge and the size of its connection, see the total plan. Third, operating the device before running into the water, water for injection was able to observe the amount of facial surface of the water hole can be seen. Close bleed valve, open the overflow port valve device to run at this time. When the device from the observation of the oil accumulation to see the water hole when the action required to have trouble, you can hit relief valve. Note: 1. Open the device lid, stainless steel wire and clean out; 2. Unscrewed the bottom of the device up vent Plug; 3. Close the exit valve, open the overflow port valve and relief valve, washing with water. 4. With a cotton cloth to wipe the glass clean and observation hole.